How do I calculate hydraulic cylinder force?

Push force: F = P × A_bore = P × π/4 × D². Pull force: F = P × A_annular = P × π/4 × (D² − d²). Where P is pressure, D is bore diameter, d is rod diameter. Convert bar to Pa (×10⁵) or use F(kN) = P(bar) × A(cm²) / 100.

How do I calculate cylinder speed?

Extension speed: v = Q / A_bore. Retraction speed: v = Q / A_annular. Since annular area is smaller, retraction is faster for the same flow rate. Convert units: v(m/s) = Q(L/min) / (A(cm²) × 6).

What are ISO 3320 standard bore sizes?

ISO 3320 standard bore diameters (mm): 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 320, 400, 500. Rod diameters follow ISO 3320-2 series.

How do I calculate required hydraulic power?

Hydraulic power P_hyd = p × Q, where p is pressure and Q is flow rate. P(kW) = p(bar) × Q(L/min) / 600. This is the power at the cylinder — pump power is higher due to system losses (typically ÷0.85 overall efficiency).

What is the speed ratio between push and pull?

Speed ratio = A_bore / A_annular = D² / (D² − d²). For a typical 2:1 ratio cylinder (d ≈ 0.707×D), retraction is 2× faster than extension at the same flow rate.

ಉಚಿತ ಎಂಜಿನಿಯರಿಂಗ್ ಟೂಲ್

ಹೈಡ್ರಾಲಿಕ್ ಸಿಲಿಂಡರ್ ಕ್ಯಾಲ್ಕುಲೇಟರ್

ISO 3320 ಪ್ರಕಾರ push/pull ಬಲ, ಪಿಸ್ಟನ್ ವೇಗ ಮತ್ತು ಹೈಡ್ರಾಲಿಕ್ ಶಕ್ತಿಯನ್ನು ಲೆಕ್ಕಿಸಿ. F = P × A, v = Q / A, Power = P × Q.

ISO 3320ಪುಷ್ / ಪುಲ್ಬಲ / ವೇಗ / ಶಕ್ತಿ

Results

ಪುಷ್ ಬಲ (ವಿಸ್ತರಣೆ)

—

ಪುಲ್ ಬಲ (ಹಿಂಪಡೆಯುವುದು)

—

ವಿಸ್ತರಣೆ ವೇಗ

—

ಹಿಂಪಡೆಯುವ ವೇಗ

—

ಹೈಡ್ರಾಲಿಕ್ ಶಕ್ತಿ

—

ಬೋರ್ / ವಲಯಾಕಾರ ಪ್ರದೇಶ

—

ಸಿಲಿಂಡರ್ ಅಡ್ಡಮಟ್ಟ

Hydraulic Cylinder Calculator | ISO 3320 | Vibromera

Published by Nikolai Shelkovenko on ಫೆಬ್ರವರಿ 15, 2026 ಏಪ್ರಿಲ್ 5, 2026

Results

ಬಲ

ವೇಗ

ಶಕ್ತಿ

ಅಂಗಡಿ

ಬೆಂಬಲ

Contact