How is centrifugal force on a fan blade calculated?

Centrifugal force F = m × R × ω², where m is blade mass in kg, R is the distance from the rotation axis to the blade center of gravity in meters, and ω = 2π·n/60 is angular velocity in rad/s. The result is in Newtons.

What is the force-to-weight ratio and why does it matter?

The force-to-weight ratio is centrifugal force divided by the blade weight (m×g). It tells you how many times the gravitational force the blade experiences. A ratio of 1000 means the blade 'feels' 1000× its own weight. This is critical for blade root stress, fastener design, and fatigue life assessment.

What is a safe tip speed for industrial fans?

Typical maximum tip speeds: carbon steel impellers 80–120 m/s, stainless steel 60–90 m/s, aluminum 100–150 m/s, FRP/fiberglass 60–80 m/s. Higher tip speeds increase centrifugal stress and noise. Critical applications may limit tip speed to 60 m/s.

Why do ID fans experience more centrifugal force than FD fans?

ID (Induced Draft) fans typically handle hot, dirty gas and have larger, heavier blades at greater radii than FD (Forced Draft) fans. Combined with similar or higher speeds, this results in significantly greater centrifugal forces on ID fan blades.

How does centrifugal force relate to fan balancing?

Centrifugal force from unbalance (uneven mass distribution) causes vibration. Even a small mass difference between blades creates a net unbalance force at the shaft. Proper balancing ensures the centrifugal forces from all blades cancel out, leaving minimal net force on the bearings.

Free Engineering Tool

ফ্যান ব্লেড সেন্ট্রিফিউগাল ফোর্স ক্যালকুলেটর

Calculate centrifugal force on fan blades for ID and FD fans. Get force per blade, total force, force-to-weight ratio, and tip speed.

ID / FD Fans Force per Blade Tip Speed

Results

Force per Blade

—

Force per Blade (kN)

—

Force-to-Weight Ratio

—

Total Force (All Blades)

—

Tip Speed

—

Centrifugal Force on a Fan Blade

m — blade mass (kg)
R — distance from axis to blade CG (m) — enter in mm, converted internally
ω = 2π·n/60 — angular velocity (rad/s)

Force-to-Weight Ratio

Tip Speed

Tip speed is calculated using the blade CG radius. For actual impeller tip speed, use the outer tip radius.

Practical Example

Example — ID Fan Blade

Given: Blade mass = 15 kg, CG radius = 800 mm, Speed = 1485 RPM

ω = 2π × 1485 / 60 = 155.5 rad/s

F = 15 × 0.8 × 155.5² = 290,340 N = 290.3 kN

Force/Weight = 290,340 / (15 × 9.81) = 1,972×

Tip speed at CG = 0.8 × 155.5 = 124.4 m/s

⚠️ Note: These forces are per blade acting on the blade root. The net force on bearings depends on balance quality — ideally, all blade forces cancel. Mass differences between blades create the unbalance force measured during balancing.

পাখা ব্লেড কেন্দ্রীয় বল ক্যালকুলেটর | ID/FD পাখা

Published by Nikolai Shelkovenko on ফেব্রুয়ারি 15, 2026 ফেব্রুয়ারি 15, 2026

Results

Centrifugal Force on a Fan Blade

Force-to-Weight Ratio

Tip Speed

Practical Example

দোকান

Support

Contact